[1]胡振球,彭再武,黄炫方,等.基于双脉冲试验的双IGBT 模块母线回路寄生电感快速计算方法[J].控制与信息技术,2018,(05):26-30.[doi:10.13889/j.issn.2096-5427.2018.05.006]
 HU Zhenqiu,PENG Zaiwu,HUANG Xuanfang,et al.A Fast Calculation Method of Parasitic Inductances in the Bus Circuit of Double- IGBT Module Based on Double-pulse Experiment[J].High Power Converter Technology,2018,(05):26-30.[doi:10.13889/j.issn.2096-5427.2018.05.006]
点击复制

基于双脉冲试验的双IGBT 模块母线回路寄生电感快速计算方法()
分享到:

《控制与信息技术》[ISSN:2095-3631/CN:43-1486/U]

卷:
期数:
2018年05期
页码:
26-30
栏目:
电力与传动控制
出版日期:
2018-10-05

文章信息/Info

Title:
A Fast Calculation Method of Parasitic Inductances in the Bus Circuit of Double- IGBT Module Based on Double-pulse Experiment
文章编号:
2096-5427(2018)05-0026-05
作者:
胡振球彭再武黄炫方尹志刚黄宜山
(湖南中车时代电动汽车股份有限公司,湖南株洲 412007)
Author(s):
HU Zhenqiu PENG Zaiwu HUANG XuanfangYIN Zhigang HUANG Yishan
( Hunan CRRC Times Electric Vehicle Co., Ltd., Zhuzhou, Hunan 412007, China)
关键词:
寄生电感IGBT 模块双脉冲试验关断波形参数计算
Keywords:
parasitic inductance IGBT module double-pulse experiment turn-off waveform parameter calculation
分类号:
TM46
DOI:
10.13889/j.issn.2096-5427.2018.05.006
文献标志码:
A
摘要:
双IGBT 模块上承受的过电压会导致系统可以控制的电流幅值减小,系统的过压保护值下降,从而限制控制策略的实施。该过电压的大小受整个回路寄生电感的影响,为了在设计之初控制该参数,需要对整个回路上各部件及其联接方式形成的电感值都提出要求。文章提出一种双IGBT 模块母线回路寄生电感快速计算方法,其利用双脉冲试验关断波形进行寄生电感参数计算,只需少量数据即可完成母线回路寄生电感的估算,进而对各部件提出电感值要求。通过计算结果对比可知, 该方法与采用开通波形计算方法相比,具有符合项目正向设计原则、计算速度快等特点。
Abstract:
Voltage spike suffered by double-IGBT module will lower the current that system can control and pull down the safety threshold, which restricts the control scheme to be used. The overvoltage is determined by the parasitic inductances in the circuit. In order to control this parameter at the initial period of system design, it is necessary to figure out a method to calculate the parasitic inductances. In this paper, it presented a fast calculation method for the parasitic inductances of double-IGBT module bus circuit, which uses the turnoff waveform of double-pulse experiment. Only a small amount of data is needed to calculate the parasitic inductances of every part in the circuit, and then the design requirements of each part can be given. Compared with the calculation method using turn-on waveform of double-pulse experiment, the results show that the proposed method meets positive design principle and has faster computing speed.

参考文献/References:

[1]陈明翊,马伯乐,陈玉其,等.低感母排技术在 IGBT 变流器中的应用[J]. 大功率变流技术,2012(6):14-17.
CHEN M Y,MA B L,CHEN Y Q,et al. Application of Low Stray Inductance Bus-bar Technology in IGBT Converter[J]. High Power Converter Technology,2012(6):14-17.
[2]ZHU H, HEFNER A R, LAI J S. Characterization of power electronics system interconnect parasitics using time domain reflectometry[J]. IEEE Transactions on Power Electronics, 1999, 2(4):1937-1943.
[3]陈材,裴雪军,陈宇,等.基于开关瞬态过程分析的大容量变换器杂散参数抽取方法[J].中国电机工程学报,2011, 31(21):40-47.
CHEN C, PEI X J, CHEN Y, et al. A Stray Parameter Extraction Method for High Power Converters Based onTurn-on/off Transient Analysis[J]. Proceedings of the CSEE,2011,31(21):40-47.
[4]冯高辉,袁立强,赵争鸣,等. 基于开关瞬态过程分析的母排杂散电感提取方法研究[J]. 中国电机工程学报,2014, 34(36):6442-6449.
 FENG G H,YUAN L Q,ZHAO Z M, et al. A Novel Stray Inductance Extraction Method for Bus Bars Based on Turn-on/off Transient Process[J]. Proceedings of the CSEE,2014,34(36): 6442-6449.
[5]HEEB H, RUEHLI A E. Three-Dimensional Interconnect Analysis Using Partial Element Equivalent Circuits[J]. IEEE Transactions on Circuits & Systems I Fundamental Theory & Applications, 1992,CAS-39(11):974-982.
[6]汪鋆,杨兵建,徐枝新,等. 750 kVA 高功率密度二极管钳位型三电平通用变流模块的低感叠层母线排设计[J]. 中国电机工程学报,2010,30(18):47-54.
WANG J, YANG B J, XU Z X, et al. Configuration of Low Inductive Laminated Bus Bar in 750 kVA NPC Three-level Universal Converter Module of High Power Density[J]. Proceedings of the CSEE ,2010,30(18):47-54.
[7]李方正,孙旭东,黄立培,等. 大容量变流器复杂形状直流母线的PEEC 建模[J]. 清华大学学报(自然科学版),2009, 49(8):1089-1092.
LI F Z, SUN X D, HUANG L P, et al. PEEC modeling of complex DC buses in high power converters[J]. Journal of Tsinghua University(Science and Technology) ,2009,49(8):1089-1092.
[8]裴雪军. PWM 逆变器传导电磁干扰的研究[D]. 武汉:华中科技大学,2004.
[9]于华龙,赵争鸣,袁立强,等. 高压IGBT 串联变换器直流母排设计与杂散参数分析[J]. 清华大学学报(自然科学版), 2014,54(4):540-545.
LIU J P, MA Z Y, SUN B T,et al. Optimal Design of Stray Inductance of Busbar in Two-level IGCT Power Module[J]. High Power Converter Technology,2015(6):14-19.
[10]刘建平,马振宇,孙保涛,等. 两电平IGCT 功率模块母线杂散电感优化设计[J]. 大功率变流技术,2015(6):14-19.
LIU J P, MA Z Y, SUN B T,et al. Optimal Design of Stray Inductance of Busbar in Two-level IGCT Power Module[J]. High Power Converter Technology,2015(6):14-19.

相似文献/References:

[1]陈明锋,雷万钧,付翀丽,等.T 型三电平结构SVG 的损耗研究[J].控制与信息技术,2015,(04):56.[doi:10.13889/j.issn.2095-3631.2015.04.011]
 CHEN Mingfeng,LEI Wanjun,FU Chongli,et al.Research on the Loss of Three-level T-type Inverter in SVG[J].High Power Converter Technology,2015,(05):56.[doi:10.13889/j.issn.2095-3631.2015.04.011]
[2]Takayuki Kushima,Katsunori Azuma,Yasuhiro Nemoto,等.具有优化沟槽HiGT 结构的3.3 kV/1 800 A IGBT及其模块优化设计[J].控制与信息技术,2015,(02):52.[doi:10.13889/j.issn.2095-3631.2015.02.011]
 Takayuki Kushima,Katsunori Azuma,Yasuhiro Nemoto,et al.3.3 kV/1 800 A IGBT Module with Advanced Trench HiGT Structure and Its Module Design Optimization[J].High Power Converter Technology,2015,(05):52.[doi:10.13889/j.issn.2095-3631.2015.02.011]
[3]王彦刚,戴小平,吴义伯,等.IGBT 模块功率损耗的产生机理、计算及模拟[J].控制与信息技术,2015,(02):62.[doi:10.13889/j.issn.2095-3631.2015.02.013]
 WANG Yangang,DAI Xiaoping,WU Yibo,et al.The Mechanism, Calculation and Simulation of Power Loss for IGBT Modules[J].High Power Converter Technology,2015,(05):62.[doi:10.13889/j.issn.2095-3631.2015.02.013]
[4]方 杰,彭勇殿,窦泽春,等.高压IGBT 模块中AlN 衬板的局部放电特性研究[J].控制与信息技术,2015,(05):38.[doi:10.13889/j.issn.2095-3631.2015.05.008]
 FANG Jie,PENG Yongdian,DOU Zechun,et al.Research on Partial Discharge Behavior of AlN Substrate in High Voltage IGBT Module[J].High Power Converter Technology,2015,(05):38.[doi:10.13889/j.issn.2095-3631.2015.05.008]
[5]李世平,奉琴,陈彦,等.IGBT模块中续流二极管关断过程失效机理分析[J].控制与信息技术,2014,(05):28.[doi:10.13889/j.issn.2095-3631.2014.05.006]
 LI Shiping,FENG Qin,CHEN Yan,et al.Analysis of Turn-off Failure Mechanism for the Freewheeling Diode in IGBT Module[J].High Power Converter Technology,2014,(05):28.[doi:10.13889/j.issn.2095-3631.2014.05.006]
[6]彭乐.二极管中点箝位型三电平逆变器低感母排的叠层布置[J].控制与信息技术,2014,(02):14.[doi:10.13889/j.issn.2095-3631.2014.02.005]
 PENGLe.Layout of Laminated Bus Bar for Diode Neutral Point Clamped Three-level Inverter[J].High Power Converter Technology,2014,(05):14.[doi:10.13889/j.issn.2095-3631.2014.02.005]
[7]李 寒,曾 雄,徐凝华,等.超声扫描在IGBT 模块质量分析中的应用[J].控制与信息技术,2016,(02):30.[doi:10.13889/j.issn.2095-3631.2016.02.007]
 LI Han,ZENG Xiong,XU Ninghua,et al.Application of Acoustic Scanning Technology in Quality Analysis of IGBT Module[J].High Power Converter Technology,2016,(05):30.[doi:10.13889/j.issn.2095-3631.2016.02.007]
[8]文 驰,李保国,熊 辉,等.IGBT 模块杂散电感分析与仿真[J].控制与信息技术,2016,(04):30.[doi:10.13889/j.issn.2095-3631.2016.04.006]
 WEN Chi,LI Baoguo,XIONG Hui,et al.Analysis and Simulation of Stray Inductance of IGBT Module[J].High Power Converter Technology,2016,(05):30.[doi:10.13889/j.issn.2095-3631.2016.04.006]
[9]徐凝华,吴义伯,刘国友,等.混合动力/电动汽车用IGBT功率模块的最新封装技术[J].控制与信息技术,2013,(01):1.[doi:10.13889/j.issn.2095-3631.2013.01.001]
 XU Ning-hua,WU Yi-bo,LIU Guo-you,et al.The Latest Packing Technology for IGBT Module in HEV/EV Application[J].High Power Converter Technology,2013,(05):1.[doi:10.13889/j.issn.2095-3631.2013.01.001]
[10]李诚瞻,常桂钦,彭勇殿,等.一种低感封装的1 200 V 混合碳化硅功率模块[J].控制与信息技术,2016,(05):71.[doi:10.13889/j.issn.2095-3631.2016.05.015]
 LI Chengzhan,CHANG Guiqin,PENG Yongdian,et al.1 200 V Hybrid SiC Power Module with Low Stray Inductance[J].High Power Converter Technology,2016,(05):71.[doi:10.13889/j.issn.2095-3631.2016.05.015]

备注/Memo

备注/Memo:
收稿日期:2018-01-11
 作者简介:胡振球(1987-),男,工程师,主要从事电动汽车用逆变器设计工作。
更新日期/Last Update: 2018-10-18